Archive for the ‘Uncategorized’ Category

http://www.sacbee.com/news/local/health-and-medicine/article150908817.html

Rip Ray

Posted: May 19, 2017 by gamegetterII in Uncategorized

RIP Ray – gone way too young.

Your sisters, brother and all of us who grew up with you n kinda sorta helped you to become the man that you were- we miss you Ray. So do all the youngsters who you were showing the right way to be in life.

We miss you Ray- may you find eternal peace…

Larry, Mark, Buster, Red dog, white dog, Debi, Antoinette, big Ang,Marshall, Bev, Roy, Gary, Big Al,Piglet, and all of our kids n grand kids.

See you on the other side Ray- no one can ever say you done them wrong.

Jeez dude- I did way more could be construed as wrong shit than you- I should be underground or in an urn- not you.

Fuck dude-I’d trade places with you if I could.

You were a better man than me.

Peace out Ray- maybe we’ll meet on the other side.

You sure as hell didn’t deserve to go before me.

Love you bro- may you find eternal peace.

Larry

Robert Gore's avatarSTRAIGHT LINE LOGIC

The Republicans have compiled a dismal record of failure, repudiating most if not all of their supposed ideological premises. From Laurence M. Vance at lewrockwell.com:

Another Republican revolution has now failed.

A Republican revolution can be defined as a time when Republicans gained control of both Houses of Congress and therefore were in a position to severely limit the federal government.

There have been five Republican revolutions in modern times, and they have all ended in failure.

The first Republican revolution occurred in 1946 when Republicans regained control of both Houses of Congress after four elections of FDR to the presidency and years of Democratic rule. With a Democrat in the White House (Harry Truman), their hands were somewhat tied, and they lost control of the Congress in the next election. Unfortunately, however, the Republicans joined with Truman in passing the National Security Act of 1947 which created the CIA…

View original post 250 more words

http://knuckledraggin.com/2017/05/in-case-you-were-wondering-2/

https://theintercept.com/2017/05/16/the-bizarre-story-behind-the-fbis-fake-documentary-about-the-bundy-family/?utm_source=The+Rutherford+Institute&utm_campaign=d910a8f64b-EMAIL_CAMPAIGN_2017_05_15&utm_medium=email&utm_term=0_d7ffde3304-d910a8f64b-42109549

Stuff You Should be Able to Make Yourself

Posted: May 17, 2017 by gamegetterII in Uncategorized

The picture shows the flywheel off an old 8hp Briggs and Stratton engine.

The piece of steel with the big bolt in center and two smaller long bolts is the flywheel puller I made in about a half hour- 45 minutes.

I originally made the puller for pulling a hub and bearing off an old tractor.

I just took the piece of steel and drilled and tapped center hole for big bolt- that’s what applies force to shaft. The original outer two holes were for pulling hub and bearing off tractor axle shaft.

To make it into flywheel puller I only had to drill two new holes and use two long 1/4-20 bolts with stop nuts. The bolts threaded into the two holes in flywheel.
Used a ratchet with correct socket for bolt and after threading two long bolts into tapped holes in flywheel, kept tightening bolt until flywheel popped loose.

This is the kind of stuff you need to be able to figure out and make in your garage/ shop.

If you ain’t mechanically inclined- get someone in your group who is.

This puller was easy to make and the only specialized tool was the tap.

I have thousands of nuts, bolts, washers and lots of pieces of angle iron, round stock steel, sheet steel and bar stock steel.

I save stuff like that for times like when I needed to make pullers for various reasons, and for when I need to make repairs on equipment or vehicles.

Helps to have a welder and cutting torches.

For this little project I only needed a cut off wheel on angle grinder to cut thick chunk of steel, drill press with right sized bits, and I used bench grinder to round off sharp edges, plus the tap and oil for drill bits and tap.



https://www.nraila.org/articles/20170516/new-study-shows-how-gun-control-has-not-slowed-violence-in-mexico

John W. Whitehead's avatarJohn W. Whitehead, Constitutional Attorney

“The means of defense against foreign danger have been always the instruments of tyranny at home.” ― James Madison

Who designed the malware worm that is now wreaking havoc on tens of thousands of computers internationally by hackers demanding a king’s ransom? The U.S. government.

Who is the biggest black market buyer and stockpiler of cyberweapons (weaponized malware that can be used to hack into computer systems, spy on citizens, and destabilize vast computer networks)? The U.S. government.

What country has one the deadliest arsenals of weapons of mass destruction? The U.S. government.

Who is the largest weapons manufacturer and exporter in the world, such that they are literally arming the world? The U.S. government.

Which is the only country to ever use a nuclear weapon in wartime? The United States.

How did Saddam Hussein build Iraq’s massive arsenal of tanks, planes, missiles, and chemical weapons during the…

View original post 1,717 more words

I think the million dollars worth is an exaggeration, but damn the car had to reek of weed and hash- why would they even need a dog?

Then there’s the fact that a recent SCOTUS case held that police can not detain you while they wait for drug dogs to get to location.

This guy might beat the charges.

My guess is he’s got a good lawyer on retainer.

http://www.news5cleveland.com/news/local-news/oh-summit/1-million-in-marijuana-hashish-and-liquid-hash-oil-seized-in-summit-county

The Best Laid Plans

Posted: May 16, 2017 by gamegetterII in Uncategorized